CREATE PROCEDURE GetPagingData_bigfun
            @tblName varchar(255), -- 表名
            @strGetFields varchar(1000) = '*', -- 需要返回的列
            @fldName varchar(255)=', -- 排序的字段名
            @PageSize int = 10, -- 頁尺寸
            @PageIndex int = 1, -- 頁碼
            @doCount bit = 0, -- 返回記錄總數, 非 0 值則返回
            @OrderType bit = 0, -- 設置排序類型, 非 0 值則降序
            @strWhere varchar(1500) = ' -- 查詢條件 (注意: 不要加 where)
            AS
            declare @strSQL varchar(5000) -- 主語句
            declare @strTmp varchar(110) -- 臨時變量
            declare @strOrder varchar(400) -- 排序類型
            if @doCount != 0
            begin
            if @strWhere !='
            set @strSQL = 'select count(*) as Total from [' + @tblName + '] where '+@strWhere
            else
            set @strSQL = 'select count(*) as Total from [' + @tblName + ']'
            end
            --以上代碼的意思是如果@doCount傳遞過來的不是0，就執行總數統計。以下的所有代碼都是@doCount為0的情況︰
            else
            begin
            if @OrderType != 0 --如果@OrderType不是0，就執行降序，這句很重要！
            begin
            set @strTmp = '<(select min'
            set @strOrder = ' order by [' + @fldName +'] desc'
            end
            else
            begin
            set @strTmp = '>(select max'
            set @strOrder = ' order by [' + @fldName +'] asc'
            end
            if @PageIndex = 1 --如果是第一頁就執行以上代碼，這樣會加快執行速度
            begin
            if @strWhere != '
            set @strSQL = 'select top ' + str(@PageSize) +' '+@strGetFields+ '
            from [' + @tblName + '] where ' + @strWhere + ' ' + @strOrder
            else
            set @strSQL = 'select top ' + str(@PageSize) +' '+@strGetFields+ '
            from ['+ @tblName + '] '+ @strOrder
            end
            else
            begin --以下代碼賦予了@strSQL以真正執行的SQL代碼　
            if @strWhere != ''
            set @strSQL = 'select top ' + str(@PageSize) +' '+@strGetFields+ '
            from ['+ @tblName + '] where [' + @fldName + ']' + @strTmp + '(['+ @fldName + '])
            from (select top ' + str((@PageIndex-1)*@PageSize) + ' ['+ @fldName + ']
            from [' + @tblName + ']
            where ' + @strWhere + ' '+ @strOrder + ') as tblTmp)
            and ' + @strWhere + ' ' + @strOrder
            else
            set @strSQL = 'select top ' + str(@PageSize) +' '+@strGetFields+ '
            from ['+ @tblName + '] where [' + @fldName + ']' + @strTmp + '(['+ @fldName + '])
            from (select top ' + str((@PageIndex-1)*@PageSize) + ' ['+ @fldName + '"]
            from [' + @tblName + ']' + @strOrder + ') as tblTmp)'+ @strOrder
            end
            end
            exec (@strSQL)
            GO

CREATE procedure p_splitpage
            @sql nvarchar(4000),--要執行的sql語句
            @page int=1, --要顯示的頁碼
            @pageSize int,--每頁的大小
            @pageCount int=0 out,--總頁數
            @recordCount int=0 out,--總記錄數
            @SearchTime int=0 out
            as
            declare @usetime datetime
            set @usetime=getdate()
            set nocount on
            declare @p1 int
            exec sp_cursoropen @p1 output,@sql,@scrollopt=1,@ccopt=1,@rowcount=@pagecount output
            set @recordCount = @pageCount
            select @pagecount=ceiling(1.0*@pagecount/@pagesize)
            ,@page=(@page-1)*@pagesize+1
            exec sp_cursorfetch @p1,16,@page,@pagesize
            exec sp_cursorclose @p1
            set  @SearchTime=datediff(ms,@usetime,getdate())
            print @SearchTime
            GO